Shenzhen furniture factory to introduce: panel furniture office furniture material is very flexible, styles the myriads of changes, so the one listed by consumers repeng. Of course you want to choose to suit their own furniture plate to learn more knowledge. Here we bring you the market, friends are most concerned about the type of furniture materials, I hope my friends to buy furniture for more!

Shenzhen furniture factory furniture plate
the main material is industrial production standards board, 2.44 meters long, 1.22 meters wide, there are a lot of thickness, material variety, here only introduce several commonly used.

Shenzhen furniture factory fiber board
has low density fiber board and medium density fiber board two, is generally used in medium density fiberboard, thickness of 15mm, 18mm suitable for doing wardrobe, bookcase, 3-5mm used to make non load bearing plate, such as the bottom plate of the drawer. Characteristics of
fiber board is a low density, easily affected with damp, processing dust, vertical machining (such as screw holes, etc.) is easy to crack, if there is no table saws, bench drill, does not recommend the use of fiber board DIY.

Shenzhen furniture factory is moistureproof particles are added in the production process in a certain proportion of the substrate (usually green), melamine board forum Tarim friends say is moistureproof board, moisture-proof plate is common in heavy grade particleboard + moisture particles + melamine decorative surface made of hot pressing, the thickness of 16mm, suitable for kitchen cabinets, bathroom cabinets and damp furniture, wardrobe, bookcase, of course do shoe can also. Moistureproof board density fiberboard, moistureproof performance is far higher than the fiber board, is not easy to crack, more suitable for DIY.

Shenzhen furniture factory is also called the big core board, the upper and lower surfaces for the two single board, middle rubber pressure mosaic of small wooden. With respect to the fiber board, moisture-proof plate, surface roughness characteristics, joinery board has the standard plate not easy to deformation, but also has the characteristics of natural wood, good nail holding ability, can use nails joint. The general decoration company will adopt the joinery board, using a nail gun joint of high speed and high efficiency. For DIY, temporarily not found this board have what advantage.
 
Shenzhen furniture factory plywood plywood by the
multilayer veneer and glue pressed, common has three layers, five layers, so it is also called the three plywood, plywood. Because of the vertical and horizontal agglutination suppression, physical, mechanical properties of plywood of vertical and horizontal directions are almost the same, is obviously superior to the natural wood, natural wood characteristics while retaining good nail holding ability, can use nails joint. Plywood for force strong furniture, there are many wood friends plywood to make tools, electric circular saw to saw saw bench.

Shenzhen furniture factory and a consistent performance connection board
these two kinds of materials and wood, equivalent to the factory the planks for wide plate, usually like wood and do not want to own plate wood friends, I have not used.
hardware

furniture factory screw
this is very common, use a screwdriver, fiber board, moisture-proof board using fiber board screw, the other near the wood properties of the plate with wood screws.

furniture factory of the three in one connection
three in a connecting piece by the eccentric connecting rod, embedded parts, three parts, used in furniture, convenient and beautiful, strong and durable, and can be assembled and disassembled for many times, many furniture manufacturers use, DIY can also be used but need certain technology, generally no bench drill, drill, the installation of a three in one connector need accurately in two plate position drill 3 holes, but also depth can not have too big deviation, use electric drill operation has certain difficulty, the efficiency is low.

Shenzhen office furniture factory production to open the door of the need to use the concealed hinge, a whole covered (Quan Gai), half shade (Ban Gai, half open), open (inner) three, is generally the most outside of the cabinet door cabinets full cover hinge, door hinge using the middle half cover a built-in cabinet door, you need to use the full hinge.

Shenzhen office furniture factory door guide
sliding doors are installed in the upper end use, also installed in the end, according to the specific need to use.

Shenzhen office furniture factory drawer guide rail
installation drawer, a pulley type (section two) and ball type (section three) two, pulley type is cheap, noisy, ball type are more expensive but the push and pull, very smooth and no noise.

Shenzhen office furniture factory in
drawer, door handles, variety, choose according to personal preference.

Shenzhen office furniture factory support
board support, making the shelves, shoe cabinet, shelf layer plate support, has the characteristics of plate position can be adjusted, types are more.

Shenzhen office furniture factory

Shenzhen office furniture factory white latex
fireproof board, wooden tenon joint use.

Shenzhen furniture factory adhesive

patch edge use. Many kinds of
glue, and don't have to use the glue, the forum what glue has examples.
paint, water paint, I have not used, in this was not introduced.

furniture factory Shenzhen surface decoration material
panel furniture generally use the veneer, rarely used paint, here are a few common veneer material.

Shenzhen office furniture factory is silica material or calcareous material as the main raw material, fiber material, lightweight aggregate, adhesives and chemical additives mixed with a certain proportion of
, the decorative sheet made of autoclaved technology. Fire board for outer surface of furniture veneer thickness, generally at about 1mm, very much the appearance of variety, decorative characteristics than fire characteristics.

Shenzhen office furniture factory is a user panel furniture cutting edge, PVC edge banding, metal edge, thin wood edge banding.

Shenzhen furniture wood grain paper
wood grain paper before using more, now generally used to fire board.

finally bring you little skill difference between fake furniture:

furniture structural firmness. One is clearance furniture door, drawer gap, if the gap is big, the rough work, will be a long time deformation; two is a single box or a double box, usually, in addition to outside a plywood, furniture inside should be attached with a layer of the panel, which is called double bag double box, box package of furniture is beautiful and strong. The paint is good or bad. Whether there is a paint streak? The angular position of paint coating is too thick? There are cracks or bubble? These are to be checked. Have to ask a salesperson, a few furniture paint. Of course, the number is better.

from the hinge shafts and drill a hole in that panel furniture timber is medium density or particle board, one of the best method is to carefully observe the hinge slot and hole is exposed, the internal structure of the local, can be seen or used a shaving board, medium density board. The use of hardware, free port portfolio is the largest furniture the advantages, so the quality of the quality of connection and the whole furniture is closely related to import your furniture on your.

panel furniture is used in paper veneer and veneer, the most convenient way is to observe patterns, wood veneer knot, color and texture changes of nature, another is the hand touch, feel different. Furniture plate edge is very important to pay attention to the merits Fengbian materials, attention to the edge is not smooth, tilt phenomenon. In particular, it Is it right? Six side edge -- although the formaldehyde free binder, but man-made board in the production process will be more or less volatile gas Fengbian tight, of course, is good for living environment!